#UG NX 7.5 SYSTEM REQUIREMENTS WINDOWS 10#
Windows 10 64-bit Editions: Windows 10, Pro and Enterprise (1) Yes (professional version of Creo Elements/Direct Modeling) Yes (through the online Creo Elements/Direct Modeling Express Forum) between isolated circuits (at 100 VDC)ĥ10 VAC for 1 min between isolated circuits, leakage current: 5 mA max.Ĭonnected to a CPU Unit or a Communication Control Unit 1.10 W max.Connected to a Communications Coupler Unit 0.70 W max.Ĭonnected to a CPU Unit or a Communication Control Unit 1.10 W max.Creo Elements/Direct Modeling Express 8.0Įnglish, German, Italian, Japanese, Simplified Chinese (Between IOV and all output terminals)Ģ0 MΩ min.
indicator, indicator, indicator, indicatorġ.2 V max. Screwless clamping terminal block (16 terminals) Safety Input Units NX-SIH400/SID800 Unit name NX1P2 CPU Units or Communications Coupler Units cannot be connected.: None. Only NX102 CPU Units and Communication Control Units can be connected. indicator, indicator, seven-segment indicatorĬurrent capacity of I/O power supply terminals indicator, indicator, indicator, indicator, indicator, Number of originators that can be connected with Number of CIP Safety originator connections The value is the total number of CIP Safety originator connections, CIP Safety target connections, and FSoE master connections. This is the maximum number of Safety I/O connections that can be set to this Unit. Safety Control Units Safety CPU Units NX-SL5500/SL5700 Unit name You can change the port number in the Unit Settings on the Sysmac Studio. (total of 32 with two logical ports)Maximum number of servers that can communicate at one time: 16 per portġ6 per port (total of 32 with two logical ports)ĭo not set the same port number for more than one TCP/UDP service. Maximum number of clients that can communicate at one time: 16 per port Do not set the same port number for more than one TCP/UDP service. The built-in EtherNet/IP port uses the TCP/UDP port numbers shown in the following table. (Data is refreshed over the network at preset intervals and does not depend on the number of nodes.)
Packet intervals can be set independently for each connection. There is no limitation when an external Ethernet switch is used. The built-in switching ports support up to 50 nodes. Shielded twisted-pair (STP) cable, Category 5, 5e or higherġ00 m max. If tag data links are being used, use 100Base-TX. Sysmac Studio connection, tag data links, CIP message communications, FTP server, automatic clock adjustment (NTP client), SNMP (agent), DNS (client), BOOTP (client), TCP/UDP message serviceġ00Base-TX or 10Base-T (100Base-TX is recommended.) The following table shows the specifications of the built-in EtherNet/IP port of the Communication Control Unit. Installation orientation and restrictions Screwless clamping terminal block (8 terminals) No isolation: Between the Unit power supply terminal and NX Unit power supplyĬurrent consumption from I/O power supply No isolation: Between the Unit power supply terminal and internal circuit The actual configurable number can be calculated as follows: 254. −25 to 70☌ (with no condensation or icing)Ģ or less: Conforms to JIS B3502 and IEC 61131-2.Ĭategory II: Conforms to JIS B3502 and IEC 61131-2.ġ00 minutes each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total)ġ47 m/s 2, 3 times each in X, Y, and Z directions General Specifications Itemġ0% to 95% (with no condensation or icing)
The NX-series Communication Control Units are also registered for RCM, EAC, and KC compliance. NX-series Communication Control Unit Certification body The NX-series Safety Control Units are also registered for RCM, EAC, and KC compliance. Requirements for PLe (Performance Level e) and for safety category 4 in EN ISO13849-1 Requirements for SIL 3 (Safety Integrity Level 3) in IEC 61508, IEC/EN 62061, (Functional Safety of Electrical/Electronic/Programmable Electronic Safety-related Systems)
The NX-series Safety Control Units allow you to build a safety control system that meets the following standards. Only NX-SL5500/5700 have obtained IEC 61131-6 and FSPC certifications. Each model of licenses does not include any DVD. DVDs and licenses are available individually. Please purchase a DVD and required number of licenses the first time you purchase the Sysmac Studio. The maximum load current depends on the installation orientation and ambient temperature.
#UG NX 7.5 SYSTEM REQUIREMENTS MANUAL#
For detail of connectable OMRON special safety input devices, refer to NX-series User's Manual Safety Control Unit/Communication Control Unit (Cat. Various OMRON special safety input devices can be connected directly without a special controller.
0 kommentar(er)
